www国产亚洲精品久久网站-久久精品免费观看国产-无码日本精品一区二区片-国内少妇高潮嗷嗷叫在线播放-国产综合久久亚洲综合

Maintenance

Emergency Hotline
+86-577-63706661

Routine Maintenance and failure analysis

Use and Maintenance

The Maintenance and Maintenance cycle of the reducer is mainly based on the following working conditions: Working Hours: 8 hours a day; Working System: contact work; input speed: 1500 RPM; maximum oil temperature: 85 °C (worm gear 90 °C) . If working conditions change, the cycle should be adjusted accordingly. After 500 working hours, the reducer should be first oil change, at least once a year, the reducer thoroughly check, according to the motor operation manual motor Maintenance.

Grease Lubrication

The Grease lubricated part of the reducer produced by our company, except for double sealed bearings, adopts the straight-through pressing oil-filling Cup structure. When lubricating this part, the grease gun is used to inject the lubricating point into the oil cup. Note: When Changing Grease, do not mix grease of different soap base.

Oil Seal replacement

Remove the oil seal from the reducer using a tool. Look Out! In the process of removing the oil seal, tools can not be inserted into the bias or too deep, so as to avoid damage to the shaft diameter, bearing and box. Grease the oil seal on the box or Flange, and evenly coat the inner and outer edges of the oil seal. The oil is sealed into the box body by means of an assembly fixture.

High bearing position temperature

Reason: The oil level of the reducer is too low; the lubricating oil is used too long; the bearing is damaged. Corrective measures: check the oil level; check the quality of Lubricating Oil; please contact our company, if necessary, please replace the bearings.

Operating temperature too high

REASONS: Too High Oil level of the reducer; too long use of lubricating oil; too many magazines in lubricating oil; too much dust on the surface of the motor fan cover or reducer; the back stop rotating failure or stuck. Corrective measures: check the oil level; check the quality of Lubricating Oil; Oil Change; clean the dust on the motor fan cover or reducer; please contact our company, if necessary, please replace the backstop.

Oil Spill A. B. From the end cover of the box. C. From the reducer Flange. D. From the oil seal of the output shaft. From the motor oil seal. Somewhere else

Reasons: The reducer is not ventilated; for a, B, box and end cover or joint seal is not correct or screw hole leakage; for C, D, Oil seal damage; other reasons caused by oil leakage. Corrective measures: replace the Ventilation Cup; tighten the sealing tape on the bolt again, if it is still leaking oil, please contact us; check the oil seal, if necessary to replace the new oil seal; please contact us.

Leaking oil from the vent plug

Reason: The reducer oil level is too high; frequent cold start. Corrective action: check oil level.

The input part works and the output part does not

Reasons: flat key damage, hole with or shaft with the block ring off; gear and other transmission parts damage. Corrective Action: Please contact our company.

VIDEO

Back To Top 主站蜘蛛池模板: 成年片色大黄全免费软件到| 国产情侣一区二区三区| 人人妻人人爽人人做夜欢视频九色 | 成年片色大黄全免费网站久久| 人妻熟女αⅴ一区二区三区| 人妻综合专区第一页| 女人自慰疯狂喷水| 亚洲国产三级在线观看| 人妻精品动漫h无码中字| 韩国美女视频黄是免费| 国产真实乱子伦清晰对白| 国产中文字幕乱人伦在线观看| 亚洲 精品 综合 精品 自拍| 天天夜碰日日摸日日澡性色av| 中文字幕一区二区三区精华液| 国产精品成人影院久久久| 亚洲精品久久久久avwww潮水| 精品无人区卡卡二卡三乱码| 欧美成人高清视频a在线看| 人妻无码中文字幕一区二区三区| 欧美日韩国产va另类| 尤物yw午夜国产精品大臿蕉| 精品国产av无码一道| 熟妇的味道hd中文字幕| 久久久久99人妻一区二区三区| 亚洲多毛妓女毛茸茸的| 免费看撕开奶罩揉吮奶头视频| 尤物yw193无码点击进入| 国产亚洲欧洲综合5388| 一区二区三区在线 | 中国| 亚洲成av人片在线观看www | 国产妇女馒头高清泬20p多| 丰满少妇熟乱xxxxx视频| 麻花传媒在线观看免费| 777午夜福利理伦电影网| 久久久www成人免费精品| 国产美女视频国产视视频| 久久精品国产曰本波多野结衣 | 美腿制服丝袜国产亚洲| 国产在线拍揄自揄拍无码| 人妻av中文字幕无码专区|